CODELOCKS 5OOO ELECTRONIC Bedienungsanleitung PDF herunterladen (Seite 2)

Program 01 ENTER NEW USER CODE

Master Code

● 01 ● User Code ID (eg 05)

New Code

(eg 4321) ●

Result = New code 4321 entered at User Code ID 05 ●

Program 02 SUSPEND USER CODE

Master Code

● 02 ●

User Code ID (eg 05) ●

Result = User Code at ID 05 suspended ● ●

Program 03 RESTORE USER CODE

Master Code

● 03 ●

User code ID (eg 05) ●

Result = User Code at ID 05 restored ●

Program 04 SUSPEND ALL USER CODES

Master Code

● 04 ●

Result = All User Codes suspended ● ●

Program 05 RESTORE ALL USER CODES

Master Code

● 05 ●

Result = All User Codes restored ●

Program 06 SET UNLOCK TIME

Master Code

● 06

● enter open time (range 2 – 9 secs) ●

Result = After code entry the lock will unlock for the set time

Program 07 ONE TIME USER CODE

Master Code

● 07

● enter one time code (eg 4321) ●

Result = User Code 4321 will only work once and then be removed from memory

Program 08 SET CODE FREE MODE

Master Code

● 08 ●

Result = Lock will be continuously unlocked

Program 09 CANCEL CODE FREE MODE

Master Code

● 09 ●

Result = Lock will revert to normal operation

Program 10 CHANGE MASTER CODE

Master Code

● 10

● enter length of Master Code followed by new Master Code

(eg 6–123456)

● confirm length of Master code followed by new Master code (6–123456) ●

Result = Master Code now changed to #123456. Note: If the length of the Master Code is

changed then all previous User Codes will be deleted

Program 11 CANCEL EMERGENCY OPEN MODE

Master Code

● 11 ●

Result = The emergency unlocked condition via REM 2 will be cancelled and the lock will revert

to normal operation

Program 12 DELETE ALL USER CODES

Master Code

● 12

● 12 ● (7 secs)

Result = All User Codes will be cleared from the memory

● Code accepted

● Code rejected

● ● Code(s) valid

but suspended

■ The lock memory will store 90 different

User Codes, each identified by a User Code

ID - 01 to 90.

■ A new code will be rejected if it is already

in the memory.

■ Codes may be 4, 5 or 6 digits long.

■ The length of the Master Code determines

the length of the User Codes.

■ The lock is delivered with the factory set

Master Code #1234

■ You are advised to change the Master

Code immediately after installation –

(see Program 10)

■ The Master Code always has the # prefix

■ When in Programming Mode a Program

Code must be entered within 5 seconds,

otherwise the lock will revert to normal.

■ The

may be used at any time to clear a

wrong entry and revert to normal.

■ If the Master Code is changed to another

of the same length then all the User

Codes will be retained.

■ If the Master Code is changed to one of a

different length then all the User Codes

will be deleted.

OPERATING INSTRUCTIONS

UNLOCK TIME The factory pre-set UNLOCK

time is 4 seconds. This may be changed –

(see Program 06).

PENALTY TIME Entering 3 incorrect User

Codes will cause the lock to suspend activity for

a penalty time of 10 seconds.

CODE FREE MODE If Code Free Mode is

required on a regular basis then it is advisable

to set it mechanically by key, as follows:

Turn the key clockwise 90 degrees, return it

to the horizontal and remove it. The lever

handle should now retract the latch without

using a code.

To reset the lock to Normal Mode turn the key

90 degrees anti-clockwise, return to horizontal

and remove it. The lever handle will not now

retract the latch without first entering a valid

code. Note that Program 08 may be used to set

the lock into Code Free Mode. If left in this Code

Free Access Mode electronically, the lock can

remain so for up to 18 months.

REVERTING TO FACTORY SETTING If the

Master Code is not known the lock memory can

be cleared and made to revert to the factory

Master Code as follows:

1 Remove one battery

2 Press and hold the ‘0’ button, replace the

battery, the Blue LED will flash twice, beep will

sound twice, then release the ‘0’ button.

3 Within 3 seconds press the ‘*’ button 3 times

and the Blue LED will flash twice. The lock will

have reverted to the factory set Master Code,

#1234, and all other settings will be erased.

REMOTE RELEASE OPTION The lock has 2

sets of terminals for remote release, labelled

REM 1 and REM 2 on the printed circuit board in

the front housing. Cables are provided with the

lock for these connections.

REM 1 is intended for use where there is a need

to allow a visitor to open the door after having

been identified by intercom or by sight from

within. REM 1 would be connected to a

pushbutton on a reception desk, or to the

appropriate button on an intercom. Pushing the

button would cause the Blue LED to light and

would release the lock for the normal set time.

REM 2 is intended for use where there is a need

for the door to be released by an alarm system,

such as a fire alarm. This enables emergency

personnel to rapidly check that no one is

trapped/overlooked in classrooms, wards, guest

rooms, etc during an emergency evacuation, or

during a fire drill. When activated by an alarm

REM 2 will maintain the unlocked condition for

30 minutes. During this time the red LED will

flash once every second to indicate the

unlocked condition. The lock will automatically

revert to normal after 30 minutes. If required

Program 11 can be used to revert the lock to

normal before the 30 minute period has

finished.

BATTERY POWER The Codelock 5000 should

provide well in excess of 500,000 openings, of

4 seconds each, from 4 x AA cells rated at

2,900 mAh.

LOW BATTERY When the battery power is

low the Red LED will flash 5 times before the

Blue LED flashes to signal acceptance of the

code. Batteries should be changed as soon as

this happens.

CODES PROGRAMMING

1 2

Kommentare zu diesen Handbüchern

Keine Kommentare

CODELOCKS 5OOO ELECTRONIC Bedienungsanleitung Seite 2

Kommentare zu diesen Handbüchern